1 Version: 3.30 Doc. No: 2012092501
10 Chapter 2: Installation ID address S/W: 256; DIP Switch: 64 Interface RS-485; Half-Simplex Baud Rate 1200 / 2400 / 4800 / 9600 BPS (Se
11 Chapter 2: Installation 2-3. Baud Rate Setup There is an 8-pins switch (Red one) on PCB as showing below: Baud Rate (Pin 7 an
12 Chapter 2: Installation 11 OFF OFF ON ON OFF OFF 12 ON OFF ON ON OFF OFF 13 OFF ON ON ON OFF OFF 14 ON ON ON ON OFF OFF 15 OFF OFF OFF
13 Chapter 2: Installation 44 ON OFF ON ON OFF ON 45 OFF ON ON ON OFF ON 46 ON ON ON ON OFF ON 47 OFF OFF OFF OFF ON ON 48 ON OFF OFF OFF
14 Chapter 2: Installation 2-5. Product with Ceiling Mount Installation 2-5-1. Ceiling Mount Model: BCO-27L BCO-27L Dimension
15 Chapter 3: Operation 2-6-1. Wall Mount Model: BWO-27S 2-6-2.1 BWO-27S Dimension 2-6-2.2 Installation Procedure: Please
16 Chapter 3: Operation Chapter 3 Operation 3-1. General Operation 3-1-1. Camera Basic Control Function FastCam III offer basic funct
17 Chapter 3: Operation Focus Far Select Auto/Manual in the menu. (Refer to Menu Edit Manual) Under the Manual mode, please p
18 Chapter 3: Operation 3-1-2. OSD Display when power on When power on, the protocol and address will be displayed on the screen. Afte
19 Chapter 3: Operation SETUP MENU →SYSTEM SETUP DISPLAY SETUP PARAMETER SETUP RECOVERY SETUP OTHERS SETUP EXECUTION MENU EXIT 3-2-2.
2 FCC Statement This equipment has been strictly tested and reached to Class A, pursuant to part 15 of the FCC rules, which focus on providing reason
20 Chapter 3: Operation S/W ADDRESS: a.) Select <SYSTEM SETUP> in main menu b.) Press [OPEN] button or lean to right direct
21 Chapter 3: Operation B. [DISPLAY SETUP] Set information by the user what to show on the screen when user does the corre
22 Chapter 3: Operation C. [PARAMETER SETUP] It is used to setup the functions and parameters of the dome. It includes 7 sub-menus:
23 Chapter 3: Operation User may change settings of Camera <CAMERA SETUP> <FOCUS: AUTO/MANUAL > AUTO: Camera will aut
24 Chapter 3: Operation OFF: The image is never frozen. <CAMERA SETUP> <CAMERA SETUP > < MIRROR:
25 Chapter 3: Operation ON: Enable NR (Noise Reduction) function. OFF: Disable NR (Noise Reduction) function. < PRESET MODE: TRA
26 Chapter 3: Operation 2. <MOTION SETUP> <AUTO FLIP: ON/OFF> When the camera tilts downward and goes jus
27 Chapter 3: Operation ON: Enable Proportion. OFF: Disable Proportion. <ACTIVATION: ON/OFF> When dome is running tour/scan m
28 Chapter 3: Operation <DWELL TIME: 1~20> Dwell time is when dome running tour mode, how many seconds should dome stay at i
29 Chapter 3: Operation 3. <TITLE EDIT> <PRESET/CAM: CAMERA/PRE001~008> To edit each label, select the l
3 Table of Content Table of Content About This Guide ...
30 Chapter 3: Operation 4. <TOUR EDIT> <TOUR EDIT> User can program dome when running <TOUR MODE>,
31 Chapter 3: Operation 5. <SCAN EDIT> <SCAN EDIT> User can program dome when running <SCAN MODE>, e
32 Chapter 3: Operation 6. <PATTERN EDIT> <PATTERN EDIT> A pattern is a memorized, repeating, series of pa
33 Chapter 3: Operation 7. <MASK EDIT> 1. <PARAMETER SETUP> 2. <POWER ON> <MASK EDIT> Mask edit
34 Chapter 3: Operation 8. <POWER ON> <POWER ON: POWER ON/PRE01~08/SCAN/TOUR01~08/PATTERN> When dome is po
35 Chapter 3: Operation D. <RECOVERY SETUP> <RECOVERY SETUP> DELETE PRESETS Delete all the presets DEFA
36 Chapter 3: Operation E. <OTHERS SETUP> 1. <ALARM SETUP> OTHERS ALARM SET PASSWORD SETUP TV SYS
37 Chapter 3: Operation <ALARM SETUP> FastCam III has four alarm inputs, which can be programmed as N.C. or N.O. When an alar
38 Chapter 3: Operation access any of the Dome settings menus when the password setting is enabled. To set up password, move joystick
39 Chapter 3: Operation F. [EXECUTION MENU] EXCUTION MENU RUN TOUR 01~08 User can define which tour mode should run
4 About This Guide About This Guide Conventions used in this guide To make sure that you perform certain tasks properly, take note of the following
40 Chapter 4: Troubleshooting Problems Possible Causes Remedies No action and images when power on Power supply damaged or insuffici
5 Important Safeguards and Warning Important Safeguards and Warning It is not recommended to install this product by unqualified person. The met
6 Chapter 1: Product Introduction Chapter 1 Product Introduction Characterized as fast speed, high decision, low noise and long life,
7 Chapter 1: Product Introduction 1-2. Product Overview Parts Name Description A. Screw holes for speed dome camera bracket B. Speed dome
8 Chapter 2: Installation 1-3. Product Features Optical Zoom: 36X (f = 3.4mm~122.4mm) optical zoom. Day & Night: Switches from
9 Chapter 2: Installation Chapter 2 Installation 2-1. Specification Item/Model FDMO-36X FDMO-35X FDMO-22X Image Sensor 1/4" SONY Ex-
Commentaires sur ces manuels